And pH 10.5; i.e. only the outer and middle layer sericin was removed from around the silk fibroin fiber. When the pH was increased to 11.0, the degumming rate rose to 23 and when the pH was increased to 11.50, the degumming rate increased to 26 , MedChemExpress Fexinidazole indicating the inner layer of sericin close to the silk fibroin was removed completely [30]. When the pH was increased to 12.00, the degumming rate increased very little, from 26 to 27 . In the preparation process, the generation of pH 12.0 SAEW was much slower than that of pH 11.5 SAEW; therefore, pH 11.5 SAEW was used in the subsequent experiments.Effect of Boiling Time on Silk Degumming RateThe change of cocoon degumming rate as the boiling time in SAEW was increased from 5 min to 60 min as shown in Figure 2b. The degumming rate of boiling in SAEW for 5 min was 23 and this increased to 26 when the boiling time was increased to 10 min; increasing the boiling time to 20, 40 or 60 min 11967625 had no further effect on the degumming rate, indicating that all of the sericin had been removed from around the fibroin fiber. Therefore, a boiling time of 20 min in pH 11.50 SAEW was used in the subsequent experiments.Effect of SAEW Volume on the Silk Degumming RateAs shown in Figure 2c, the degumming rate was ,25 for a cocoon shell to SAEW ratio of 1:40 (W/V), which indicated that most or all of the sericin was removed from around the silk fibroin fiber. When the ratio was 1:80, the degumming rate was increased to a maximum of nearly 27 but further increase of the ratio had no significant effect. These results show that the optimum ratio of cocoon 23148522 shell to pH 11.50 SAEW for degumming is 1:40,80 (W/ V) and the following experiments were all done at ratios within this range.Surface Property of Silk Fibroin FiberThe surface properties of silk fibroin fibers obtained by the Na2CO3, SAEW and Felypressin chemical information neutral soap degumming methods observed in a scanning electron microscope (SEM; Hitachi S-4700 cold field emission microscope) at a magnification of 10006 are shown in Figure 3. These single filaments of silk fibroin are ,10 mm in diameter but they are not standard cylindrical and their morphology is irregular. SEM observations showed that the surface of single filaments of the degummed silk fibroin was smooth and there was no evident difference among the products of the three degumming methods used in this study.Table 1. The alkaline ions and content in various water (mg/L).Differential Scanning Calorimetry (DSC)The DSC curves of the silk fibroin fibers obtained by the Na2CO3, SAEW and neutral soap degumming methods are shown in Figure 4. The glass transition temperature was very similar for these silk fibroin fibers, indicating that these degumming methods had no significant impact on the fiber structure. However, the impact of these degumming methods on the thermal decomposition temperature of silk fibroin fibers was clear. The silk fiber degummed in neutral soap solution had the highest thermal decomposition temperature of 329.30uC, indicating this type of silk fiber has the greatest thermal stability. The thermal stability of fibers prepared by treatment with Na2CO3 was the least and the thermal decomposition temperature was 322.96uC, which is 6.5uC lower than that in the neutral soap group, indicating the silk fibroin fiber was altered to a considerable extent. The thermal stability of the silk fibroin fiber degummed in pH 11.50 SAEWDetected elements Water Ordinary tap water Ultrapure water Acidic electrolyzed water.And pH 10.5; i.e. only the outer and middle layer sericin was removed from around the silk fibroin fiber. When the pH was increased to 11.0, the degumming rate rose to 23 and when the pH was increased to 11.50, the degumming rate increased to 26 , indicating the inner layer of sericin close to the silk fibroin was removed completely [30]. When the pH was increased to 12.00, the degumming rate increased very little, from 26 to 27 . In the preparation process, the generation of pH 12.0 SAEW was much slower than that of pH 11.5 SAEW; therefore, pH 11.5 SAEW was used in the subsequent experiments.Effect of Boiling Time on Silk Degumming RateThe change of cocoon degumming rate as the boiling time in SAEW was increased from 5 min to 60 min as shown in Figure 2b. The degumming rate of boiling in SAEW for 5 min was 23 and this increased to 26 when the boiling time was increased to 10 min; increasing the boiling time to 20, 40 or 60 min 11967625 had no further effect on the degumming rate, indicating that all of the sericin had been removed from around the fibroin fiber. Therefore, a boiling time of 20 min in pH 11.50 SAEW was used in the subsequent experiments.Effect of SAEW Volume on the Silk Degumming RateAs shown in Figure 2c, the degumming rate was ,25 for a cocoon shell to SAEW ratio of 1:40 (W/V), which indicated that most or all of the sericin was removed from around the silk fibroin fiber. When the ratio was 1:80, the degumming rate was increased to a maximum of nearly 27 but further increase of the ratio had no significant effect. These results show that the optimum ratio of cocoon 23148522 shell to pH 11.50 SAEW for degumming is 1:40,80 (W/ V) and the following experiments were all done at ratios within this range.Surface Property of Silk Fibroin FiberThe surface properties of silk fibroin fibers obtained by the Na2CO3, SAEW and neutral soap degumming methods observed in a scanning electron microscope (SEM; Hitachi S-4700 cold field emission microscope) at a magnification of 10006 are shown in Figure 3. These single filaments of silk fibroin are ,10 mm in diameter but they are not standard cylindrical and their morphology is irregular. SEM observations showed that the surface of single filaments of the degummed silk fibroin was smooth and there was no evident difference among the products of the three degumming methods used in this study.Table 1. The alkaline ions and content in various water (mg/L).Differential Scanning Calorimetry (DSC)The DSC curves of the silk fibroin fibers obtained by the Na2CO3, SAEW and neutral soap degumming methods are shown in Figure 4. The glass transition temperature was very similar for these silk fibroin fibers, indicating that these degumming methods had no significant impact on the fiber structure. However, the impact of these degumming methods on the thermal decomposition temperature of silk fibroin fibers was clear. The silk fiber degummed in neutral soap solution had the highest thermal decomposition temperature of 329.30uC, indicating this type of silk fiber has the greatest thermal stability. The thermal stability of fibers prepared by treatment with Na2CO3 was the least and the thermal decomposition temperature was 322.96uC, which is 6.5uC lower than that in the neutral soap group, indicating the silk fibroin fiber was altered to a considerable extent. The thermal stability of the silk fibroin fiber degummed in pH 11.50 SAEWDetected elements Water Ordinary tap water Ultrapure water Acidic electrolyzed water.
